In the TV portal, arrow down to the Adult channel (channel viewing screen) (has lock by channel), hit OK, a small box will come on screen, enter 0000, thats zero,zero,zero,zero, and OK. This will get the channel open. If you wish to change it from 0000, go to settings in outer portal, OK, now on Parental Control, OK, in the top password, enter 0000, on keyboard cursor over to info enter and OK, hit home button, open keyboard, enter YOUR new password, cursor over to info enter OK, hit home button and repeat again your NEW password, info enter OK, home key, cursor down to OK at bottom and your done. REMEMBER to make it simple to remember, every time you go to a Adult channel, you will need to enter this password.
Mag 254 Parental Password...
↧
↧
How To Place or Remove A Lock From Any Channel
While in the channel list "guide" pres the APP button on the desired channel, enter the default password "0000", press OK. This will either place a lock on unlocked channels, or remove a lock from a locked channel, ex. 484 TVHOT.
This works very well on the 254. If the channel is locked to begin with I had to enter the control code first and then press the APP button enter the control code again and then the lock was removed.
To install the lock on to a channel press the APP button and enter the control code
This works very well on the 254. If the channel is locked to begin with I had to enter the control code first and then press the APP button enter the control code again and then the lock was removed.
To install the lock on to a channel press the APP button and enter the control code
↧
Reset info from INFOMIR
How to enter the BIOS setup (bootloader menu) MAG-200/250?
Power off STB MAG200/250.
Press and hold the «menu» on the remote (or the power button on the front panel).
Without releasing the «menu» (or the power button on the front panel) Power on STB MAG200/250.
If there is no image on the screen maybe your TV doesn't support PAL system.
If there is no image then complete next steps:
Unplug power of STB
Press and hold Menu button on RC (direct your RC to STB)
Plug power on STB with holding Menu button
Hold Menu button during 10 seconds.
Switch PAL - NTSC with single press on red button F1 on RC.
How to see the firmware version and device information?
To enter in BIOS menu.
Choose «Upgrade Menu» and press right on the remote control. If this step is missing, go to next step (this step can be absent if the second copy of bootloader doesn't on).
Device info and press right on the remote control:
Vendor - Manufactory identifier.
Model - Model identifier.
Ver. Hardware - Version of network board realization.
Serial Number - Serial number.
MAC address - Physical address of network interface.
Loader Info and press right on the remote control:
Version Number - Bootloader version (if the second bootloader is on, then you will see the second bootloader version).
Date & Time - Date and Time of bootloader version.
Image info press right on the remote control:
Version - Software version.
Description - Full version description.
How to reset BIOS MAG-200/250 to factory settings?
Enter The BIOS.
choose Def. Settings.
press the right.
confirm by pressing the OK.
Select Exit & Save to save and exit. STB will reboot automatically.
Maybe, it will be necessary to change boot mode: NAND, NAND2 or DHCP.
Change boot mode DHCP/NAND/NAND2.
Change boot mode DHCP/NAND/NAND2
Enter The BIOS.
Select Upgrade Menu , right click on the remote control.
Select Boot Mode and pressing the remote control right to set the boot mode DHCP, NAND or NAND2.
Select Exit & Save and press on the remote control to the right.
Confirm OK.
Printable version
Power off STB MAG200/250.
Press and hold the «menu» on the remote (or the power button on the front panel).
Without releasing the «menu» (or the power button on the front panel) Power on STB MAG200/250.
If there is no image on the screen maybe your TV doesn't support PAL system.
If there is no image then complete next steps:
Unplug power of STB
Press and hold Menu button on RC (direct your RC to STB)
Plug power on STB with holding Menu button
Hold Menu button during 10 seconds.
Switch PAL - NTSC with single press on red button F1 on RC.
How to see the firmware version and device information?
To enter in BIOS menu.
Choose «Upgrade Menu» and press right on the remote control. If this step is missing, go to next step (this step can be absent if the second copy of bootloader doesn't on).
Device info and press right on the remote control:
Vendor - Manufactory identifier.
Model - Model identifier.
Ver. Hardware - Version of network board realization.
Serial Number - Serial number.
MAC address - Physical address of network interface.
Loader Info and press right on the remote control:
Version Number - Bootloader version (if the second bootloader is on, then you will see the second bootloader version).
Date & Time - Date and Time of bootloader version.
Image info press right on the remote control:
Version - Software version.
Description - Full version description.
How to reset BIOS MAG-200/250 to factory settings?
Enter The BIOS.
choose Def. Settings.
press the right.
confirm by pressing the OK.
Select Exit & Save to save and exit. STB will reboot automatically.
Maybe, it will be necessary to change boot mode: NAND, NAND2 or DHCP.
Change boot mode DHCP/NAND/NAND2.
Change boot mode DHCP/NAND/NAND2
Enter The BIOS.
Select Upgrade Menu , right click on the remote control.
Select Boot Mode and pressing the remote control right to set the boot mode DHCP, NAND or NAND2.
Select Exit & Save and press on the remote control to the right.
Confirm OK.
Printable version
↧
Portal/reboot quick switch
PRESS SET or SETUP/cog or F9 on a keyboard
move to RESTART PORTAL
or
move to REBOOT DEVICE
or a.n.other ....
JOB DONE!!!
move to RESTART PORTAL
or
move to REBOOT DEVICE
or a.n.other ....
JOB DONE!!!
↧
Inter portal quick jump
If you push the system button, the one under the F4 key, it will take you to the
Inter portal system settings and if you hit the exit key it will take you back to the outer portal.
Inter portal system settings and if you hit the exit key it will take you back to the outer portal.
↧
↧
MAG using a KEYBOARD
Heres some shortcuts:
POWER Alt+U
CHANNEL_PREV Shift+Tab
CHANNEL_NEXT Tab
EXIT Esc
REFRESH F5
UP UP ARROW
DOWN DOWN ARROW
LEFT LEFT ARROW
RIGHT RIGHT ARROW
OK Enter
PAGE_NEXT Page Down
PAGE_PREV Page Up
NEXT Page Down
PREV Page Up
VOL_UP NUMPAD +
VOL_DOWN NUMPAD -
RED F1
GREEN F2
YELLOW F3
BLUE F4
SERVICES F9
TV F10
PHONE F8
EPG F8
WEB F12
APP F12
REW Alt+B
FFWD Alt+F
PLAY Alt+R
PAUSE Alt+R
CONTINUE Alt+R
STOP Alt+S
REC Alt+W
INFO Alt+Y
FRAME F6
AUDIO Alt+G
NULL Alt+L
KEYBOARD Alt+L
USB_UNMOUNTED Alt+Q
USB_MOUNTED Alt+P
POWER Alt+U
CHANNEL_PREV Shift+Tab
CHANNEL_NEXT Tab
EXIT Esc
REFRESH F5
UP UP ARROW
DOWN DOWN ARROW
LEFT LEFT ARROW
RIGHT RIGHT ARROW
OK Enter
PAGE_NEXT Page Down
PAGE_PREV Page Up
NEXT Page Down
PREV Page Up
VOL_UP NUMPAD +
VOL_DOWN NUMPAD -
RED F1
GREEN F2
YELLOW F3
BLUE F4
SERVICES F9
TV F10
PHONE F8
EPG F8
WEB F12
APP F12
REW Alt+B
FFWD Alt+F
PLAY Alt+R
PAUSE Alt+R
CONTINUE Alt+R
STOP Alt+S
REC Alt+W
INFO Alt+Y
FRAME F6
AUDIO Alt+G
NULL Alt+L
KEYBOARD Alt+L
USB_UNMOUNTED Alt+Q
USB_MOUNTED Alt+P
↧
Wipe out !! Factory reset
HOW TO WIPE OUT ALL SETTINGS IN MAG254 how to
PART1 - DOWNLOAD SOFTWARE
1) Download and extract from
HTML Code:
Bootstrap_254.clean (RENAME as Bootstrap)
imageupdate
3) Place the both files (imageupdate and Bootstrap) into a folder called mag254 on your USB stick
PART2 WIPE THE BOX
PLUG IN POWER SUPPLY
HOLD MENU BUTTON
Enter The BIOS.
choose Def. Settings.
press the right.
IGNORE MESSAGE ´WRONG IMAGE´
confirm by pressing the OK.
Select Exit & Save to save and exit.
STB will reboot automatically.
message ´Tftp load ´ will be on screen
power lead out
![]()
PART 3 - FLASH THE BOX
1) Plug the USB Stick in the REAR USB Port
2) Power the STB on - press and hold the MENU button (just above the volume up button - you have to be quick)
3) Go to Upgrade Tools, then USB bootstrap.
This will then flash the STB with all your portal settings
![]()
PART1 - DOWNLOAD SOFTWARE
1) Download and extract from
HTML Code:
Code:
http://soft.infomir.com.uaimageupdate
3) Place the both files (imageupdate and Bootstrap) into a folder called mag254 on your USB stick
PART2 WIPE THE BOX
PLUG IN POWER SUPPLY
HOLD MENU BUTTON
Enter The BIOS.
choose Def. Settings.
press the right.
IGNORE MESSAGE ´WRONG IMAGE´
confirm by pressing the OK.
Select Exit & Save to save and exit.
STB will reboot automatically.
message ´Tftp load ´ will be on screen
power lead out
PART 3 - FLASH THE BOX
1) Plug the USB Stick in the REAR USB Port
2) Power the STB on - press and hold the MENU button (just above the volume up button - you have to be quick)
3) Go to Upgrade Tools, then USB bootstrap.
This will then flash the STB with all your portal settings
↧
NTSC to HD
NTSC to HD
INTERNAL MAG254 SETTINGS FOR HDMI FLAT SCREEN TVs for 720P
DO NOT use this if you are ONLY using the RCA plugs (yellow/red/white) as you will lose the picture
the sound can still be used thru the red/white cables for a hi-fi
HDMI CABLE MUST BE CONNECTED AND A PICTURE ON THE SCREEN BEFORE YOU START
1.press SET
2.press down button to VIDEO and press OK
3.VIDEO OUTPUT MODE left button change to 720p (changes your TV from 1948 NTSC system to 2015 HIGH DEFINITION )
4.press down button to
5.GRAPHIC RESOLUTION change to 1280x720 (changes your TV from 480 lines to 720 lines)
6.press OK to save
7. press RED (F1) button
8.AUTO FRAME RATE right button
9 NOTICE press EXIT right button,right button
10 change to 24/60hz (24 frames per second/electric in americas)
11.HDMI/DVI (do not change leave as HDMI -if you change this you will lose sound)
12.press OK
13.EXIT,EXIT,EXIT
14.CONFIRM press OK
19.screen will go blank and box will REBOOT to TV
INTERNAL MAG254 SETTINGS FOR HDMI FLAT SCREEN TVs for 720P
DO NOT use this if you are ONLY using the RCA plugs (yellow/red/white) as you will lose the picture
the sound can still be used thru the red/white cables for a hi-fi
HDMI CABLE MUST BE CONNECTED AND A PICTURE ON THE SCREEN BEFORE YOU START
1.press SET
2.press down button to VIDEO and press OK
3.VIDEO OUTPUT MODE left button change to 720p (changes your TV from 1948 NTSC system to 2015 HIGH DEFINITION )
4.press down button to
5.GRAPHIC RESOLUTION change to 1280x720 (changes your TV from 480 lines to 720 lines)
6.press OK to save
7. press RED (F1) button
8.AUTO FRAME RATE right button
9 NOTICE press EXIT right button,right button
10 change to 24/60hz (24 frames per second/electric in americas)
11.HDMI/DVI (do not change leave as HDMI -if you change this you will lose sound)
12.press OK
13.EXIT,EXIT,EXIT
14.CONFIRM press OK
19.screen will go blank and box will REBOOT to TV
↧
what is iptv
What is iptv and how does it work? is it something to do with dishnetworks? if so are the satellite dishes needed or is it something else entirely?
↧
↧
no channels ECM?
I have IKS dish and NFPS and i can't connect to any of the six server ports that i donated for. It has been this way since about 3:00 pm yesterday.Whats the problem?
↧
IPTV setup
1. Of course you start by putting batteries in the remote, hooking it to your tv, plugging in your network cable, and turning it on.
2. Once it boots up to the inner portal go to "Settings" and select "Interface". This is where you tell it where to go when it loads up, changes weather to C or F, etc. I set my weather to Fahrenheit here and ok to save. Exit back out to "Settings"
3. Now go to "System Settings" and select "Network" to set it up. "Auto (DHCP)" will work for most users. For wireless you need an usb adapter so we won't go into that now.
4. Select "Auto update software" and set auto update to enabled. Press the green F2 button to update now. Then exit.
5. Exit out twice to "System Settings" menu and now go to Servers.
5. Click "General" and put in a timeserver. pool.ntp.org works. Use the "KB" button on your remote to bring up the on screen keyboard. This is where we fix your time. Press ok to save and then exit once back to "Servers' menu.
7. Click "Portals" and enter your server info. There are 2 there. For "Portal 1 name "here you enter the URL given"
. then press ok to save and exit back twice to "System Settings" again.
8. Click "Video" and choose what you want to use or what your tv wants to use. The bottom left button on your remote is the aspect button and will show the list, remember this for future reference. Press ok to save and exit back out to "System Settings" again.
9. This time select "Advanced Settings" These are pretty self-explanatory. Language, time zone closest to you, and where you find buffer size if you need to set it now or later. Left mine at 0. Make sure to press ok to save and reboot your STB.
10. After the reboot it will boot into the IPTV portal. If it loads into a tv channel or black screen press exit to see the portal page. Here you will see TV, Videoclub, etc.
11. Scroll it over to "Settings" and click it.
12. Here you can set parental control if needed. Select "Localization" now and fix your settings there. Set them as needed with a city somewhere close to where you are if yours is not listed. Exit out and scroll through the rest. If you need to change anything do so now. Some of the options are the same as in the inner portal.
13. For "Portal" it is best to leave it at main menu if you have limited bandwidth, so it doesn't come on to live tv without anyone watching it.
14. Towards the bottom you will see "Go to the inner portal", this is how you get back to the inner portal if needed.
15. Now exit out and watch some tv. Videoclub is where the movies are and tv is where, um, the tv is
If at any time you get bored, stumped, or want to learn more go into settings and exit back out into the inner portal. You'll see a book icon there named "Menu Guide" that has a wealth of information. Check it out and get a little more comfortable with the terms and usage of your mag receiver.
Any time you're in the inner portal, pressing exit a few times will boot you back into the IPTV portal.
1. Of course you start by putting batteries in the remote, hooking it to your tv, plugging in your network cable, and turning it on.
2. Once it boots up to the inner portal go to "Settings" and select "Interface". This is where you tell it where to go when it loads up, changes weather to C or F, etc. I set my weather to Fahrenheit here and ok to save. Exit back out to "Settings"
3. Now go to "System Settings" and select "Network" to set it up. "Auto (DHCP)" will work for most users. For wireless you need an usb adapter so we won't go into that now.
4. Select "Auto update software" and set auto update to enabled. Press the green F2 button to update now. Then exit.
5. Exit out twice to "System Settings" menu and now go to Servers.
5. Click "General" and put in a timeserver. pool.ntp.org works. Use the "KB" button on your remote to bring up the on screen keyboard. This is where we fix your time. Press ok to save and then exit once back to "Servers' menu.
7. Click "Portals" and enter your server info. There are 2 there. For "Portal 1 name "here you enter the URL given"
. then press ok to save and exit back twice to "System Settings" again.
8. Click "Video" and choose what you want to use or what your tv wants to use. The bottom left button on your remote is the aspect button and will show the list, remember this for future reference. Press ok to save and exit back out to "System Settings" again.
9. This time select "Advanced Settings" These are pretty self-explanatory. Language, time zone closest to you, and where you find buffer size if you need to set it now or later. Left mine at 0. Make sure to press ok to save and reboot your STB.
10. After the reboot it will boot into the IPTV portal. If it loads into a tv channel or black screen press exit to see the portal page. Here you will see TV, Videoclub, etc.
11. Scroll it over to "Settings" and click it.
12. Here you can set parental control if needed. Select "Localization" now and fix your settings there. Set them as needed with a city somewhere close to where you are if yours is not listed. Exit out and scroll through the rest. If you need to change anything do so now. Some of the options are the same as in the inner portal.
13. For "Portal" it is best to leave it at main menu if you have limited bandwidth, so it doesn't come on to live tv without anyone watching it.
14. Towards the bottom you will see "Go to the inner portal", this is how you get back to the inner portal if needed.
15. Now exit out and watch some tv. Videoclub is where the movies are and tv is where, um, the tv is
If at any time you get bored, stumped, or want to learn more go into settings and exit back out into the inner portal. You'll see a book icon there named "Menu Guide" that has a wealth of information. Check it out and get a little more comfortable with the terms and usage of your mag receiver.
Any time you're in the inner portal, pressing exit a few times will boot you back into the IPTV portal.
I take no credit for this post. got it from another.
2. Once it boots up to the inner portal go to "Settings" and select "Interface". This is where you tell it where to go when it loads up, changes weather to C or F, etc. I set my weather to Fahrenheit here and ok to save. Exit back out to "Settings"
3. Now go to "System Settings" and select "Network" to set it up. "Auto (DHCP)" will work for most users. For wireless you need an usb adapter so we won't go into that now.
4. Select "Auto update software" and set auto update to enabled. Press the green F2 button to update now. Then exit.
5. Exit out twice to "System Settings" menu and now go to Servers.
5. Click "General" and put in a timeserver. pool.ntp.org works. Use the "KB" button on your remote to bring up the on screen keyboard. This is where we fix your time. Press ok to save and then exit once back to "Servers' menu.
7. Click "Portals" and enter your server info. There are 2 there. For "Portal 1 name "here you enter the URL given"
. then press ok to save and exit back twice to "System Settings" again.
8. Click "Video" and choose what you want to use or what your tv wants to use. The bottom left button on your remote is the aspect button and will show the list, remember this for future reference. Press ok to save and exit back out to "System Settings" again.
9. This time select "Advanced Settings" These are pretty self-explanatory. Language, time zone closest to you, and where you find buffer size if you need to set it now or later. Left mine at 0. Make sure to press ok to save and reboot your STB.
10. After the reboot it will boot into the IPTV portal. If it loads into a tv channel or black screen press exit to see the portal page. Here you will see TV, Videoclub, etc.
11. Scroll it over to "Settings" and click it.
12. Here you can set parental control if needed. Select "Localization" now and fix your settings there. Set them as needed with a city somewhere close to where you are if yours is not listed. Exit out and scroll through the rest. If you need to change anything do so now. Some of the options are the same as in the inner portal.
13. For "Portal" it is best to leave it at main menu if you have limited bandwidth, so it doesn't come on to live tv without anyone watching it.
14. Towards the bottom you will see "Go to the inner portal", this is how you get back to the inner portal if needed.
15. Now exit out and watch some tv. Videoclub is where the movies are and tv is where, um, the tv is
If at any time you get bored, stumped, or want to learn more go into settings and exit back out into the inner portal. You'll see a book icon there named "Menu Guide" that has a wealth of information. Check it out and get a little more comfortable with the terms and usage of your mag receiver.
Any time you're in the inner portal, pressing exit a few times will boot you back into the IPTV portal.
1. Of course you start by putting batteries in the remote, hooking it to your tv, plugging in your network cable, and turning it on.
2. Once it boots up to the inner portal go to "Settings" and select "Interface". This is where you tell it where to go when it loads up, changes weather to C or F, etc. I set my weather to Fahrenheit here and ok to save. Exit back out to "Settings"
3. Now go to "System Settings" and select "Network" to set it up. "Auto (DHCP)" will work for most users. For wireless you need an usb adapter so we won't go into that now.
4. Select "Auto update software" and set auto update to enabled. Press the green F2 button to update now. Then exit.
5. Exit out twice to "System Settings" menu and now go to Servers.
5. Click "General" and put in a timeserver. pool.ntp.org works. Use the "KB" button on your remote to bring up the on screen keyboard. This is where we fix your time. Press ok to save and then exit once back to "Servers' menu.
7. Click "Portals" and enter your server info. There are 2 there. For "Portal 1 name "here you enter the URL given"
. then press ok to save and exit back twice to "System Settings" again.
8. Click "Video" and choose what you want to use or what your tv wants to use. The bottom left button on your remote is the aspect button and will show the list, remember this for future reference. Press ok to save and exit back out to "System Settings" again.
9. This time select "Advanced Settings" These are pretty self-explanatory. Language, time zone closest to you, and where you find buffer size if you need to set it now or later. Left mine at 0. Make sure to press ok to save and reboot your STB.
10. After the reboot it will boot into the IPTV portal. If it loads into a tv channel or black screen press exit to see the portal page. Here you will see TV, Videoclub, etc.
11. Scroll it over to "Settings" and click it.
12. Here you can set parental control if needed. Select "Localization" now and fix your settings there. Set them as needed with a city somewhere close to where you are if yours is not listed. Exit out and scroll through the rest. If you need to change anything do so now. Some of the options are the same as in the inner portal.
13. For "Portal" it is best to leave it at main menu if you have limited bandwidth, so it doesn't come on to live tv without anyone watching it.
14. Towards the bottom you will see "Go to the inner portal", this is how you get back to the inner portal if needed.
15. Now exit out and watch some tv. Videoclub is where the movies are and tv is where, um, the tv is
If at any time you get bored, stumped, or want to learn more go into settings and exit back out into the inner portal. You'll see a book icon there named "Menu Guide" that has a wealth of information. Check it out and get a little more comfortable with the terms and usage of your mag receiver.
Any time you're in the inner portal, pressing exit a few times will boot you back into the IPTV portal.
I take no credit for this post. got it from another.
↧
mag254
deleted
↧
Rocket server
Since may 05 2015 rocket server is down in eastcost
any news why ?
any news why ?
↧
↧
What offers are out there is there a channel list ?
Hi All,
Who is offering what?
is there a list of servers available?
is there a list of channels available?
I'm up in Canada, and was very happy with one iks server, it had one local news channel, I really got used to in the morning. and yes I'm looking for that channel.
Thanks,
Steve
Who is offering what?
is there a list of servers available?
is there a list of channels available?
I'm up in Canada, and was very happy with one iks server, it had one local news channel, I really got used to in the morning. and yes I'm looking for that channel.
Thanks,
Steve
↧
"thanks a lot"
You guys are the best,up & running channels are coming back,truly you all are fta professionals:d please keep up the good work
↧
How to get infomir logo back on a mag 250
Open "System settings" -> "Software update"
- Change current URL for updating to hxxp://mag.infomir.com.ua/r2/imageupdate_logo
- Press "OK" and update STB
- Change current URL for updating to hxxp://mag.infomir.com.ua/r2/imageupdate_logo
- Press "OK" and update STB
↧
Mag 254 Parental Password...
In the TV portal, arrow down to the Adult channel (channel viewing screen) (has lock by channel), hit OK, a small box will come on screen, enter 0000, thats zero,zero,zero,zero, and OK. This will get the channel open. If you wish to change it from 0000, go to settings in outer portal, OK, now on Parental Control, OK, in the top password, enter 0000, on keyboard cursor over to info enter and OK, hit home button, open keyboard, enter YOUR new password, cursor over to info enter OK, hit home button and repeat again your NEW password, info enter OK, home key, cursor down to OK at bottom and your done. REMEMBER to make it simple to remember, every time you go to a Adult channel, you will need to enter this password.
↧
↧
How To Place or Remove A Lock From Any Channel
While in the channel list "guide" pres the APP button on the desired channel, enter the default password "0000", press OK. This will either place a lock on unlocked channels, or remove a lock from a locked channel, ex. 484 TVHOT.
This works very well on the 254. If the channel is locked to begin with I had to enter the control code first and then press the APP button enter the control code again and then the lock was removed.
To install the lock on to a channel press the APP button and enter the control code
This works very well on the 254. If the channel is locked to begin with I had to enter the control code first and then press the APP button enter the control code again and then the lock was removed.
To install the lock on to a channel press the APP button and enter the control code
↧
Reset info from INFOMIR
How to enter the BIOS setup (bootloader menu) MAG-200/250?
Power off STB MAG200/250.
Press and hold the «menu» on the remote (or the power button on the front panel).
Without releasing the «menu» (or the power button on the front panel) Power on STB MAG200/250.
If there is no image on the screen maybe your TV doesn't support PAL system.
If there is no image then complete next steps:
Unplug power of STB
Press and hold Menu button on RC (direct your RC to STB)
Plug power on STB with holding Menu button
Hold Menu button during 10 seconds.
Switch PAL - NTSC with single press on red button F1 on RC.
How to see the firmware version and device information?
To enter in BIOS menu.
Choose «Upgrade Menu» and press right on the remote control. If this step is missing, go to next step (this step can be absent if the second copy of bootloader doesn't on).
Device info and press right on the remote control:
Vendor - Manufactory identifier.
Model - Model identifier.
Ver. Hardware - Version of network board realization.
Serial Number - Serial number.
MAC address - Physical address of network interface.
Loader Info and press right on the remote control:
Version Number - Bootloader version (if the second bootloader is on, then you will see the second bootloader version).
Date & Time - Date and Time of bootloader version.
Image info press right on the remote control:
Version - Software version.
Description - Full version description.
How to reset BIOS MAG-200/250 to factory settings?
Enter The BIOS.
choose Def. Settings.
press the right.
confirm by pressing the OK.
Select Exit & Save to save and exit. STB will reboot automatically.
Maybe, it will be necessary to change boot mode: NAND, NAND2 or DHCP.
Change boot mode DHCP/NAND/NAND2.
Change boot mode DHCP/NAND/NAND2
Enter The BIOS.
Select Upgrade Menu , right click on the remote control.
Select Boot Mode and pressing the remote control right to set the boot mode DHCP, NAND or NAND2.
Select Exit & Save and press on the remote control to the right.
Confirm OK.
Printable version
Power off STB MAG200/250.
Press and hold the «menu» on the remote (or the power button on the front panel).
Without releasing the «menu» (or the power button on the front panel) Power on STB MAG200/250.
If there is no image on the screen maybe your TV doesn't support PAL system.
If there is no image then complete next steps:
Unplug power of STB
Press and hold Menu button on RC (direct your RC to STB)
Plug power on STB with holding Menu button
Hold Menu button during 10 seconds.
Switch PAL - NTSC with single press on red button F1 on RC.
How to see the firmware version and device information?
To enter in BIOS menu.
Choose «Upgrade Menu» and press right on the remote control. If this step is missing, go to next step (this step can be absent if the second copy of bootloader doesn't on).
Device info and press right on the remote control:
Vendor - Manufactory identifier.
Model - Model identifier.
Ver. Hardware - Version of network board realization.
Serial Number - Serial number.
MAC address - Physical address of network interface.
Loader Info and press right on the remote control:
Version Number - Bootloader version (if the second bootloader is on, then you will see the second bootloader version).
Date & Time - Date and Time of bootloader version.
Image info press right on the remote control:
Version - Software version.
Description - Full version description.
How to reset BIOS MAG-200/250 to factory settings?
Enter The BIOS.
choose Def. Settings.
press the right.
confirm by pressing the OK.
Select Exit & Save to save and exit. STB will reboot automatically.
Maybe, it will be necessary to change boot mode: NAND, NAND2 or DHCP.
Change boot mode DHCP/NAND/NAND2.
Change boot mode DHCP/NAND/NAND2
Enter The BIOS.
Select Upgrade Menu , right click on the remote control.
Select Boot Mode and pressing the remote control right to set the boot mode DHCP, NAND or NAND2.
Select Exit & Save and press on the remote control to the right.
Confirm OK.
Printable version
↧
Portal/reboot quick switch
PRESS SET or SETUP/cog or F9 on a keyboard
move to RESTART PORTAL
or
move to REBOOT DEVICE
or a.n.other ....
JOB DONE!!!
move to RESTART PORTAL
or
move to REBOOT DEVICE
or a.n.other ....
JOB DONE!!!
↧
More Pages to Explore .....
